Text Us
    Back to Home

    Rheem Water Heater Repair & Replacement in Greer, SC

    We repair and replace Rheem water heaters, gas and electric tanks and tankless. Here's what Rheem's own manuals say about the questions people ask most: lighting the pilot, the reset button, what the status light's blinks mean, and the tankless codes.

    Rheem Water Heater Repair & Replacement

    About This Service

    Our Rheem jobs include a 40-gallon gas water heater replacement in Spartanburg, where the old unit was leaking and inefficient, and a dual Rheem electric setup for a duplex rental property in Greenville, each unit with its own expansion tank and relief valve.

    On Rheem's standing-pilot gas models with a status light on the gas control, the pilot is lit with a piezo spark button, and Rheem says not to open the inner door and try to light it by hand. Its label's steps: smell all around the heater for gas, including next to the floor, before lighting. Turn the gas control knob to OFF and wait five minutes; if you smell gas, stop. Remove the outer door, turn the knob to PILOT, then hold it all the way in while pressing the spark button several times until the status light blinks, and check the flame through the sight glass. If the light doesn't start blinking after 90 seconds and the pilot isn't lit, repeat the steps. If the pilot won't stay lit after several attempts, Rheem says to turn the knob to OFF and call your service technician or gas supplier. And if any part of the heater has been under water, Rheem says not to use it: a flooded water heater must be replaced.

    The status light on those models blinks in a pattern every three seconds. One blink is normal operation. Two blinks is low thermopile voltage with the pilot lit. Four blinks means the high water temperature limit tripped, five a water temperature sensor failure, seven a gas control failure, and eight a false pilot flame signal; for those, Rheem's answer is to contact a qualified service technician. No light can mean the control is off or the pilot isn't lit. A pilot that won't stay lit when the knob is released, Rheem's troubleshooting table traces to a loose or defective thermocouple, a defective safety magnet, the gas control's single-use shut-off having opened, or the combustion shutoff device having tripped, all repairs for a qualified service technician. On these standing-pilot models, that single-use shut-off isn't resettable: if it opens, Rheem says the gas control is replaced by a qualified service technician.

    Electric Rheems do have one. When the water gets too hot, the temperature limiting control (ECO) cuts power to the element and has to be reset by hand, with the power off, by pressing the red RESET button behind the jacket access panel and insulation on standard models (behind the user interface control on e-control models). Rheem's caution comes first, though: the cause of the high temperature has to be investigated by a qualified service technician and corrected before the heater goes back in service.

    On a non-condensing Rheem tankless, code 11 means the gas shut-off valve isn't fully open, code 12 means the gas service was interrupted (or, on propane, the tank is running low), and P1 means there isn't enough water flow, so open the fixture more. 1L is lime buildup, 88 is a reminder to flush the heat exchanger or replace the water treatment filter, and 90 or 99 means the air intake or vent may be blocked; Rheem calls for 12 inches of clearance at the air intake. To clear a code, Rheem says to turn off all hot water faucets, turn the heater off, wait about 5 minutes and restart it, and if the code stays, unplug it for about 30 seconds. If a code isn't in the chart, turn the heater off and call for service.

    Water under a tank isn't always a leak. Rheem says condensation can form when a tank is first filled, or with a heavy draw of very cold incoming water, and should stop once the water heats; if it continues, check the piping and fittings for leaks. A relief valve that discharges periodically may be thermal expansion in a closed water system, and Rheem says never to plug it. Its technical bulletin says a good sign of thermal expansion is the relief valve releasing about one cup of water for each ten gallons of heater capacity with each heating cycle. Most homes here are closed systems; see our expansion tank page.

    Ruud and Richmond are part of the same family. Rheem's tank warranty is issued by Rheem Sales Company, manufacturer of Rheem, Ruud and Friedrich products, and its tankless warranty covers Rheem, Ruud, Richmond, Paloma and EcoSmart residential tankless heaters.

    Signs You May Need Rheem Water Heater Repair & Replacement

    • A pilot that won't light or won't stay lit
    • A status light blinking 4, 5, 7 or 8 times
    • No hot water from an electric heater
    • Code 11, 12 or P1 on a Rheem tankless
    • Water under the tank
    • A relief valve that drips after the heater runs

    What's Included

    • Rheem gas and electric water heater replacement
    • Pilot, thermocouple, thermopile and gas control repair
    • Electric element, thermostat and ECO repair
    • Rheem tankless code diagnosis and flushing
    • Expansion tank and relief valve service
    • Drain pan and T&P discharge piping

    Why Choose Us

    • Rheem gas, electric and tankless
    • Code and blink diagnosis before parts
    • Licensed in South Carolina and North Carolina
    • Veteran-owned local plumber in Greer

    Rheem Water Heater Repair & Replacement FAQ

    On standing-pilot models, Rheem's label says: smell for gas first, turn the knob to OFF and wait five minutes, then turn it to PILOT, hold it in and press the spark button several times until the status light blinks. If it won't stay lit after several tries, turn the knob to OFF and call a technician or your gas supplier. Never light it by hand.

    On electric models, it's the red RESET button on the high-temperature limit (ECO), behind the access panel and insulation on standard models; turn the power off before you touch it. Rheem says a qualified technician needs to find out why it tripped. On standing-pilot gas models, the gas control has a single-use shut-off instead, and Rheem says the gas control is replaced if it opens.

    On Rheem's standing-pilot gas models, the light blinks every three seconds: one blink is normal, two is low thermopile voltage, four is the high temperature limit tripped, five a temperature sensor failure, seven a gas control failure and eight a false pilot flame signal. Four and up mean call a technician.

    On Rheem's non-condensing tankless models, code 11 means the gas shut-off valve isn't fully open; check it and open it completely. Code 12 is interrupted gas service or low propane, and P1 is not enough water flow.

    Rheem's serial numbers start with the month and then the year it was made: a serial reading 12 09 D 01234 was made in December 2009.

    It depends on the model. Rheem's 6-year tank and parts warranty covers single-family homes for six years from the effective date, applies only to the original owner and isn't transferable, and doesn't cover labor. It doesn't cover damage caused by running the heater with the anode rod removed.

    They're the same family. Rheem's tank warranty is issued by the manufacturer of Rheem, Ruud and Friedrich products, and Rheem's tankless warranty covers Rheem, Ruud and Richmond tankless heaters.

    Rheem Water Heater Repair & Replacement Near You

    We provide rheem water heater repair & replacement to homeowners and businesses across the Upstate SC area. Select your city to see local service info.

    Ready to get started?

    Call us now or request a free quote — we respond within minutes.

    864-279-4461